Turquoise Brown Trout Trucker Hat
by @sunny
Jaw open, gold flank turning in the current.
A realistic brown trout on a turquoise water swirl, in golden yellow, olive and brick red, for days on the river and the drive there.
A brown trout with its jaw open, cutting through a swirl of turquoise current. Golden yellow flanks, an olive back, black spots and brick red dots finish the fish.
- Brown trout with open jaw
- Golden yellow flank, olive back
- Black spots and brick red dots
- Turquoise water with white current swirls
- Eight colour layers, painterly realism
The cap
One design, four caps. The front panel is what the paint or the dye sits on, so it changes the hat.
Trucker
The house cap — structured mid profile, foam-and-mesh back, snapback.
Specs
- Profile
- Mid profile
- Build
- 6-panel · Structured — buckram behind the front
- Crown
- 3½ in (8.9 cm)
- Visor
- Pre-curved, 2¾ in (7 cm)
- Closure
- Snapback
- Adjusts to
- 21½–24 in (54.5–61 cm)
- Airbrushed on
- Natural cotton twill
- Sublimated on
- White polyester foam
Rope cap
Structured five-panel with a near-flat brim and a cord across it.
Specs
- Profile
- Mid-high profile
- Build
- 5-panel · Structured
- Crown
- 4 in (10.2 cm)
- Visor
- Near-flat, 2⅞ in (7.3 cm), contrast rope
- Closure
- Snapback
- Adjusts to
- 21½–23¾ in (54.5–60.5 cm)
- Airbrushed on
- Stone cotton twill
- Sublimated on
- White polyester twill
Dad hat
Soft, low and unstructured — washed cotton with a strap back.
Specs
- Profile
- Low profile
- Build
- 6-panel · Unstructured — soft front
- Crown
- 3¼ in (8.3 cm)
- Visor
- Curved, 2¾ in (7 cm)
- Closure
- Strap back, brass buckle
- Adjusts to
- 21–23½ in (53.5–59.5 cm)
- Airbrushed on
- Washed khaki cotton
- Sublimated on
- White polyester twill
Five-panel camp
Flat brim, low crown, packs flat in a vest pocket.
Specs
- Profile
- Low profile
- Build
- 5-panel · Unstructured
- Crown
- 3¼ in (8.3 cm)
- Visor
- Flat, 2½ in (6.4 cm)
- Closure
- Strap back, side-release clip
- Adjusts to
- 21½–23½ in (54.5–59.5 cm)
- Airbrushed on
- Field olive nylon-cotton
- Sublimated on
- White polyester
Fit
| Cap | Profile | Crown height | Visor | Adjusts to |
|---|---|---|---|---|
| Trucker | Mid profile | 3½ in (8.9 cm) | Pre-curved, 2¾ in (7 cm) | 21½–24 in (54.5–61 cm) |
| Rope cap | Mid-high profile | 4 in (10.2 cm) | Near-flat, 2⅞ in (7.3 cm), contrast rope | 21½–23¾ in (54.5–60.5 cm) |
| Dad hat | Low profile | 3¼ in (8.3 cm) | Curved, 2¾ in (7 cm) | 21–23½ in (53.5–59.5 cm) |
| Five-panel camp | Low profile | 3¼ in (8.3 cm) | Flat, 2½ in (6.4 cm) | 21½–23½ in (54.5–59.5 cm) |
One size per cap. Run a tape around your head just above the ears, keeping it level — anything inside the range above will close on it.
Two finishes
The same design, made two ways. Pick one in the panel; the cap and the quantity are yours to choose too.
Hand airbrushed
$85 for one hat, on a trucker
Painted to order — would ship in about 2 weeks
How it is made
- How it is made
- Sprayed by hand through this design's own stencils, one layer at a time, each left to dry before the next mask goes down.
- How it looks
- Soft gradients and hand-cut stencil edges. Every cap is a little different.
- What it sits on
- On a natural cotton twill front.
- Durability and care
- Water-based paint, heat set and sealed. It takes rain and a season on a boat; spot clean with cool water, never a washing machine.
Sublimation printed
$32 for one hat, on a trucker
Printed to order — would ship in 5–7 business days
How it is made
- How it is made
- The design is printed in dye onto transfer paper, then pressed with heat so the dye soaks into the polyester fibres.
- How it looks
- Full colour edge to edge, and identical every time.
- What it sits on
- On a white polyester foam front — sublimation only takes on white polyester.
- Durability and care
- The dye is in the fibre, not on it, so it will not crack or peel. Gentle wash, air dry.
The artwork
A brown trout turns through turquoise water, mouth open, fins flared. Its belly glows golden yellow under an olive back. Black spots and brick red dots run the length of the flank, and white streaks of current curl around the tail.
Wear it to the riffle, the fly shop or the tailgate after. The fish reads from across a parking lot: a flash of gold on teal. Up close, people find the red spots and the glint in the eye.
Burnt orange shading is where the trout gets its weight. Keep it soft and low on the flank and gill plate, so the golden yellow still shows through on the belly.
The water it was painted from
White RiverOzarks, North Arkansas · AR
- River
- White River, Ozarks, North Arkansas
- States
- AR
- Fish
- Brown trout, Rainbow trout, Cutthroat trout
- Water type
- Tailwater
What arrives
- The hat
- A care card
- On a hand airbrushed hat, a numbered tag naming the water it was painted from, when the design names one
Looking after it
Hand airbrushed
- Spot clean with cool water and a soft brush. Never a washing machine.
- Keep it out of a hot car for long stretches — heat-set paint is tough, but a dashboard in July is not a test worth running.
- Reshape the brim by hand while damp.
Sublimation printed
- Spot clean, or gently hand wash in cool water. No bleach.
- Air dry. Do not iron the print.
- Reshape the brim by hand while damp.
- The dye is in the fibre, so the print will not crack or peel.
Details
Airbrush palette
- Colours
- turquoise, white, golden yellow, olive, burnt orange, black, brick red
Details
- Subject
- brown trout
- Style
- realistic painterly illustration
Make it yourself
The palette
- Turquoise
- White
- Golden yellow
- Olive
- Burnt orange
- Black
- Brick red
The layers
8 layers, in this order. Each mask comes off and the paint has to dry before the next one goes down.
- Water
- Current
- Body
- Back
- Shading
- Markings
- Red spots
- Highlights
The kit's stencil set is cut from these layers; with the cutter (12 hats and up) you cut your own from this design's layer files.
How to mix each colour
Turquoise
1 part blue, 1 part green, 2 parts white; a drop of yellow if it looks too cold
White
Opaque white from the bottle; two thin coats cover better than one thick one
Golden yellow
Mix by eye against the photograph; test on the card first
Olive
2 parts yellow, 1 part black, a drop of red to warm it
Burnt orange
1 part red to 2 parts yellow
Black
Black from the bottle, sprayed in light passes; a heavy coat bleeds
Brick red
Primary red from the bottle; a drop of yellow warms it, a drop of blue cools it
Setup
- Ventilation or a spray booth. Water-based paint still throws a fine mist, and you will be breathing it for hours.
- A half-mask respirator rated for paint mists. A dust mask is not one.
- A compressor with a moisture trap, set and tested on a card before you start: wet air spits water into the paint.
- Reducer and a cleaning pot within reach, so a clog is a ten-second fix instead of a ruined panel.
- Spray a test card for every colour before it touches the cap. Colour reads differently wet, dry and on twill.
Prep
- Lint-roll the front panel. Every fibre left on it prints as a speck in the paint.
- Mask the mesh, any seams you want clean and the whole visor, underside included, with low-tack tape and paper.
- Stretch the crown over the cap jig so the front panel is taut and curved the way it will be worn. Spraying a slack panel flat distorts the design when it is worn.
- Spray one light coat of transparent base so the colour sits on the fabric instead of soaking into it.
Layer by layer
1 · Water — 0.5 mm · 25–30 PSI
turquoise — a loose oval of water behind the fish, deeper at the edges
Mask None on the panel itself: the mesh and the visor are already masked from the prep.
Colour Turquoise — 1 part blue, 1 part green, 2 parts white; a drop of yellow if it looks too cold
- Needle
- 0.5 mm (a 0.35 mm works, it just takes longer)
- Pressure
- 25–30 PSI
- Distance
- 6–8 in from the panel
- Passes
- 3–4 light passes, building the colour
- Dry
- 10 minutes, or 60–90 seconds with a heat gun on low, before the next mask goes down
Tip Fade wet to dry and never lay one heavy coat: twill wicks paint sideways and the edge blooms.
2 · Current — 0.35 mm · 20–25 PSI
white — curling streaks and ripples swept through the water
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour White — Opaque white from the bottle; two thin coats cover better than one thick one
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
3 · Body — 0.35 mm · 20–25 PSI
golden yellow — the whole trout silhouette, belly, tail and fins
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Golden yellow — Mix by eye against the photograph; test on the card first
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
4 · Back — 0.35 mm · 20–25 PSI
olive — the dark top of the back and head, fading down into the gold
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Olive — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
5 · Shading — 0.35 mm · 20–25 PSI
burnt orange — warm shading along the flank, gill plate and fins
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Burnt orange — 1 part red to 2 parts yellow
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
6 · Markings — 0.35 mm · 20–25 PSI
black — the scattered spots, eye, jaw line and fin edges
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Black — Black from the bottle, sprayed in light passes; a heavy coat bleeds
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
7 · Red spots — 0.3 mm · 18–22 PSI
brick red — small red spots along the lateral flank
Mask The hand-cut subject stencil, inner pieces first, then the outline piece.
Colour Brick red — Primary red from the bottle; a drop of yellow warms it, a drop of blue cools it
- Needle
- 0.3 mm
- Pressure
- 18–22 PSI
- Distance
- 3–4 in from the panel
- Passes
- 2–3 passes per tone, light to dark
- Dry
- 10 minutes between tones
Tip Light tones first: a light colour over a dark one needs many coats, a dark one over a light one needs two.
8 · Highlights — 0.2–0.3 mm · 12–15 PSI
white — eye glint, belly sheen and fin tips
Mask None: freehand, with a shield card held against any hard edge.
Colour White — Opaque white from the bottle; two thin coats cover better than one thick one
- Needle
- 0.2–0.3 mm
- Pressure
- 12–15 PSI
- Distance
- 1–2 in from the panel
- Passes
- Freehand, in short controlled strokes
- Dry
- 10 minutes, then check it before you cure
Tip Low pressure, close in and moving: stop the stroke before you release the trigger.
Step by step
Mask the water oval and spray turquoise at 20 PSI with a 0.3 mm needle from about 15 cm, building the edges darker. These settings are a starting point; test on scrap first.
Cut a curved current mask and spray white streaks at 15 PSI, 0.2 mm needle, 8–10 cm away. Let it dry to the touch.
Lay the full trout silhouette mask and fill with golden yellow at 20 PSI, 0.3 mm needle, about 12 cm away, two light coats.
Shield the belly and spray olive along the back and head at 18 PSI, 0.3 mm needle, 12 cm, fading down into the gold.
Freehand burnt orange shading along the flank, gill plate and fins at 15 PSI, 0.2 mm needle, 8 cm, in thin passes.
Use a spot stencil and detail mask for black spots, eye, jaw line and fin edges at 15 PSI, 0.2 mm needle, 5–6 cm.
Place the red spot stencil and dot brick red along the flank at 12 PSI, 0.2 mm needle, about 5 cm.
Add white highlights to the eye, belly sheen and fin tips at 12 PSI, 0.2 mm needle, 4–5 cm.
Let the paint cure for 24 hours at room temperature, then heat set as the paint maker directs.
Seal with two thin coats of fabric-safe clear sealer, drying between coats.
Cure
- Heat set at 300°F / 150°C. Water-based textile paint is not wash-fast until it is heat set.
- Cap press: 3–5 minutes with a teflon sheet over the design.
- Or heat gun: 2–3 minutes per panel, keeping it moving 2–3 in off the fabric so it does not scorch.
- If you have neither, air cure for 72 hours before the cap touches water.
Seal
- Two light coats of matte fabric sealer, UV-resistant, from 8–10 in, 15 minutes apart.
- Leave it 24 hours before the cap is worn.
- Never a gloss sealer on cotton twill: it shines, cracks along the creases and looks like a sticker.
Clean-up
- Flush the brush with water, then airbrush cleaner, until it sprays clear.
- Strip the needle and wipe it toward the tip, never away from it.
- Never soak the brush body overnight.
Common mistakes
- Flooding the golden yellow: two light coats beat one heavy coat that bleeds under the mask.
- Over-darkening with burnt orange: stop early, as shading deepens once dry.
- Lifting masks on wet paint: wait until each layer is dry to the touch before removing.
- Skipping the cure: sealing too soon can cloud the colours, so give it the full 24 hours.
Tips
- Practise the olive-to-gold fade on scrap until the line between them disappears.
- Vary spot sizes slightly; identical dots make the fish look stamped.
- Keep the white current streaks moving the same way as the fish so the swim reads clearly.
- Thin the brick red a touch so the dots sit inside the gold rather than on top.
Every kit size
Trucker · kit for 1 hat
$224
Bought separately $249 · you save $25
Includes Starter airbrush set · Cap jig · and 7 more
Every item in this kit · 9 items
Blanks
- Trucker blank, natural cotton twill front$9
Stencils
- Pre-cut mylar stencil set for this design — 8 layers$18
Paint & masks
- Water-based textile airbrush colour, 2 oz — one per colour in this design$42
- Transparent base and reducer, 4 oz$7
- Low-tack masking film and ¼ in tape$8
- Matte fabric sealer, 4 oz$12
Equipment
- Starter airbrush set — 0.3 mm dual-action gravity brush, mini compressor, braided hose$129
- Cap jig — holds the crown taut while you spray$24
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 hats
$1,073
$89.42 a hat
Bought separately $1,220 · you save $147
Includes Dual-action gravity-feed airbrush · Quiet compressor with tank and moisture trap · Cap jig and two spare crown forms · Tabletop spray booth with exhaust fan · and 11 more
Every item in this kit · 15 items
Blanks
- Trucker blank, natural cotton twill front$78
Stencils
- Desktop stencil cutter, 12 in — the "stencil printer": cuts mylar from this design's layer files$299
- Stencil mylar, 7 mil, 12 × 12 in$22
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 4 oz — one per colour in this design$98
- Transparent base and reducer, 16 oz$16
- Low-tack masking film$18
- Matte fabric sealer, 16 oz$28
Equipment
- Dual-action gravity-feed airbrush, 0.3 mm$135
- Quiet compressor with tank and moisture trap$179
- Cap jig and two spare crown forms$64
- Tabletop spray booth with exhaust fan$149
- Cleaning pot, brushes and a half-mask respirator$99
- Heat gun for curing$35
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 × 12 hats
$3,124
$21.69 a hat
Bought separately $3,676 · you save $552
Includes Two dual-action gravity-feed airbrushes · Production airbrush · Twin-piston compressor with tank and two regulators · Production spray booth · and 13 more
Every item in this kit · 17 items
Blanks
- Trucker blank, natural cotton twill front$756
Stencils
- Stencil cutter-plotter, 24 in — the production "stencil printer"$649
- Stencil mylar, 7 mil, 12 × 12 in$85
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 32 oz — one per colour in this design$336
- Transparent base and reducer$49
- Low-tack masking film$54
- Matte fabric sealer$89
Equipment
- Two dual-action gravity-feed airbrushes, 0.3 mm$270
- Production airbrush, 0.5 mm, for base fades$95
- Twin-piston compressor with tank and two regulators$329
- Production spray booth, two fans$289
- Three cap jigs$192
- Cleaning station, respirator and spare cartridges$139
- Cap heat press for curing$279
- Drying rack, 24 caps$65
Guide
- Printed step-by-step guide for this designIncluded
The creator
Remixes
No remixes yet — make your own version.
Where this came from
trucker hat · made
0 — nothing entered the score yet, at the Derby's published weights, since . Views are not counted.
- brown trout
- trout
- trucker hat
- fly fishing
- turquoise
- golden yellow
- olive
- brick red
- river
- realistic
- fish art