Sunrise Rainbow Trout Trucker Hat
by @dekasso
Clear of the water, lit from behind.
A rainbow trout leaping from white spray at sunrise, in olive gold, crimson rose and sky blue, for days on the river.
A rainbow trout bursts clear of the river, body curved and jaw open, with a sunrise glowing behind it. Olive gold flanks, a crimson rose band and black speckles sit against sky blue, forest green and a spray of white water.
- Rainbow trout caught mid-leap
- Sunrise amber glow behind the fish
- Black speckles over olive gold flanks
- Crimson rose band along the side
- White spray around the tail
The cap
One design, four caps. The front panel is what the paint or the dye sits on, so it changes the hat.
Trucker
The house cap — structured mid profile, foam-and-mesh back, snapback.
Specs
- Profile
- Mid profile
- Build
- 6-panel · Structured — buckram behind the front
- Crown
- 3½ in (8.9 cm)
- Visor
- Pre-curved, 2¾ in (7 cm)
- Closure
- Snapback
- Adjusts to
- 21½–24 in (54.5–61 cm)
- Airbrushed on
- Natural cotton twill
- Sublimated on
- White polyester foam
Rope cap
Structured five-panel with a near-flat brim and a cord across it.
Specs
- Profile
- Mid-high profile
- Build
- 5-panel · Structured
- Crown
- 4 in (10.2 cm)
- Visor
- Near-flat, 2⅞ in (7.3 cm), contrast rope
- Closure
- Snapback
- Adjusts to
- 21½–23¾ in (54.5–60.5 cm)
- Airbrushed on
- Stone cotton twill
- Sublimated on
- White polyester twill
Dad hat
Soft, low and unstructured — washed cotton with a strap back.
Specs
- Profile
- Low profile
- Build
- 6-panel · Unstructured — soft front
- Crown
- 3¼ in (8.3 cm)
- Visor
- Curved, 2¾ in (7 cm)
- Closure
- Strap back, brass buckle
- Adjusts to
- 21–23½ in (53.5–59.5 cm)
- Airbrushed on
- Washed khaki cotton
- Sublimated on
- White polyester twill
Five-panel camp
Flat brim, low crown, packs flat in a vest pocket.
Specs
- Profile
- Low profile
- Build
- 5-panel · Unstructured
- Crown
- 3¼ in (8.3 cm)
- Visor
- Flat, 2½ in (6.4 cm)
- Closure
- Strap back, side-release clip
- Adjusts to
- 21½–23½ in (54.5–59.5 cm)
- Airbrushed on
- Field olive nylon-cotton
- Sublimated on
- White polyester
Fit
| Cap | Profile | Crown height | Visor | Adjusts to |
|---|---|---|---|---|
| Trucker | Mid profile | 3½ in (8.9 cm) | Pre-curved, 2¾ in (7 cm) | 21½–24 in (54.5–61 cm) |
| Rope cap | Mid-high profile | 4 in (10.2 cm) | Near-flat, 2⅞ in (7.3 cm), contrast rope | 21½–23¾ in (54.5–60.5 cm) |
| Dad hat | Low profile | 3¼ in (8.3 cm) | Curved, 2¾ in (7 cm) | 21–23½ in (53.5–59.5 cm) |
| Five-panel camp | Low profile | 3¼ in (8.3 cm) | Flat, 2½ in (6.4 cm) | 21½–23½ in (54.5–59.5 cm) |
One size per cap. Run a tape around your head just above the ears, keeping it level — anything inside the range above will close on it.
Two finishes
The same design, made two ways. Pick one in the panel; the cap and the quantity are yours to choose too.
Hand airbrushed
$85 for one hat, on a trucker
Painted to order — would ship in about 2 weeks
How it is made
- How it is made
- Sprayed by hand through this design's own stencils, one layer at a time, each left to dry before the next mask goes down.
- How it looks
- Soft gradients and hand-cut stencil edges. Every cap is a little different.
- What it sits on
- On a natural cotton twill front.
- Durability and care
- Water-based paint, heat set and sealed. It takes rain and a season on a boat; spot clean with cool water, never a washing machine.
Sublimation printed
$32 for one hat, on a trucker
Printed to order — would ship in 5–7 business days
How it is made
- How it is made
- The design is printed in dye onto transfer paper, then pressed with heat so the dye soaks into the polyester fibres.
- How it looks
- Full colour edge to edge, and identical every time.
- What it sits on
- On a white polyester foam front — sublimation only takes on white polyester.
- Durability and care
- The dye is in the fibre, not on it, so it will not crack or peel. Gentle wash, air dry.
The artwork
A rainbow trout hangs in the air, tail still in the splash. Black speckles run the length of its olive back. The red band catches the amber light coming up over the trees.
Wear it on the drive to the put-in or on a rock above the run. People see the fish first, then the sunrise behind it, then the spray. It reads from across a parking lot.
Crimson rose along the side needs a soft edge on both borders. Let it melt into the olive above and the pale belly below, so the band glows instead of sitting on top.
What arrives
- The hat
- A care card
- On a hand airbrushed hat, a numbered tag naming the water it was painted from, when the design names one
Looking after it
Hand airbrushed
- Spot clean with cool water and a soft brush. Never a washing machine.
- Keep it out of a hot car for long stretches — heat-set paint is tough, but a dashboard in July is not a test worth running.
- Reshape the brim by hand while damp.
Sublimation printed
- Spot clean, or gently hand wash in cool water. No bleach.
- Air dry. Do not iron the print.
- Reshape the brim by hand while damp.
- The dye is in the fibre, so the print will not crack or peel.
Details
Airbrush palette
- Colours
- sky blue, sunrise amber, forest green, olive gold, crimson rose, spot black, spray white
Details
- Subject
- rainbow trout
- Style
- painterly realism
Make it yourself
The palette
- Sky blue
- Sunrise amber
- Forest green
- Olive gold
- Crimson rose
- Spot black
- Spray white
The layers
7 layers, in this order. Each mask comes off and the paint has to dry before the next one goes down.
- Sky
- Sunrise glow
- Treeline and river
- Trout body
- Red band
- Spots and detail
- Splash
The kit's stencil set is cut from these layers; with the cutter (12 hats and up) you cut your own from this design's layer files.
How to mix each colour
Sky blue
1 part blue to 4 parts white, a drop of green so it does not drift purple
Sunrise amber
3 parts yellow, 1 part red, a drop of black to deepen it
Forest green
2 parts green, 1 part black, a drop of blue to cool it
Olive gold
2 parts yellow, 1 part black, a drop of red to warm it
Crimson rose
3 parts red, 1 part blue, a drop of black to deepen it
Spot black
Black from the bottle, sprayed in light passes; a heavy coat bleeds
Spray white
Opaque white from the bottle; two thin coats cover better than one thick one
Setup
- Ventilation or a spray booth. Water-based paint still throws a fine mist, and you will be breathing it for hours.
- A half-mask respirator rated for paint mists. A dust mask is not one.
- A compressor with a moisture trap, set and tested on a card before you start: wet air spits water into the paint.
- Reducer and a cleaning pot within reach, so a clog is a ten-second fix instead of a ruined panel.
- Spray a test card for every colour before it touches the cap. Colour reads differently wet, dry and on twill.
Prep
- Lint-roll the front panel. Every fibre left on it prints as a speck in the paint.
- Mask the mesh, any seams you want clean and the whole visor, underside included, with low-tack tape and paper.
- Stretch the crown over the cap jig so the front panel is taut and curved the way it will be worn. Spraying a slack panel flat distorts the design when it is worn.
- Spray one light coat of transparent base so the colour sits on the fabric instead of soaking into it.
Layer by layer
1 · Sky — 0.5 mm · 25–30 PSI
sky blue — a fade from the top left that softens toward the horizon
Mask None on the panel itself: the mesh and the visor are already masked from the prep.
Colour Sky blue — 1 part blue to 4 parts white, a drop of green so it does not drift purple
- Needle
- 0.5 mm (a 0.35 mm works, it just takes longer)
- Pressure
- 25–30 PSI
- Distance
- 6–8 in from the panel
- Passes
- 3–4 light passes, building the colour
- Dry
- 10 minutes, or 60–90 seconds with a heat gun on low, before the next mask goes down
Tip Fade wet to dry and never lay one heavy coat: twill wicks paint sideways and the edge blooms.
2 · Sunrise glow — 0.35 mm · 20–25 PSI
sunrise amber — a warm burst low on the right, behind the fish
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Sunrise amber — 3 parts yellow, 1 part red, a drop of black to deepen it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
3 · Treeline and river — 0.35 mm · 20–25 PSI
forest green — distant trees and the darker water beneath the leap
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Forest green — 2 parts green, 1 part black, a drop of blue to cool it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
4 · Trout body — 0.3 mm · 18–22 PSI
olive gold — the back and upper flanks of the fish
Mask The hand-cut subject stencil, inner pieces first, then the outline piece.
Colour Olive gold — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.3 mm
- Pressure
- 18–22 PSI
- Distance
- 3–4 in from the panel
- Passes
- 2–3 passes per tone, light to dark
- Dry
- 10 minutes between tones
Tip Light tones first: a light colour over a dark one needs many coats, a dark one over a light one needs two.
5 · Red band — 0.35 mm · 20–25 PSI
crimson rose — the stripe along the side and the blush on the gill plate
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Crimson rose — 3 parts red, 1 part blue, a drop of black to deepen it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
6 · Spots and detail — 0.35 mm · 20–25 PSI
spot black — speckles, the eye, fin edges and the mouth line
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Spot black — Black from the bottle, sprayed in light passes; a heavy coat bleeds
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
7 · Splash — 0.2–0.3 mm · 12–15 PSI
spray white — droplets, churned water around the tail and a bright belly edge
Mask None: freehand, with a shield card held against any hard edge.
Colour Spray white — Opaque white from the bottle; two thin coats cover better than one thick one
- Needle
- 0.2–0.3 mm
- Pressure
- 12–15 PSI
- Distance
- 1–2 in from the panel
- Passes
- Freehand, in short controlled strokes
- Dry
- 10 minutes, then check it before you cure
Tip Low pressure, close in and moving: stop the stroke before you release the trigger.
Step by step
Clean and dry the surface, then tape off the edges of the art area. All settings below are a starting point; test on scrap first.
Sky: no mask. Sky blue at 20 PSI, 0.3 mm needle, 15 cm away. Fade from the top left, lightening as you move down and right.
Sunrise glow: shield the sky with a loose paper mask. Sunrise amber at 18 PSI, 0.3 mm needle, 12 cm. Build a warm burst low on the right.
Treeline and river: cut a ragged treeline mask. Forest green at 20 PSI, 0.3 mm needle, 10 cm. Darken the water area under where the fish will sit.
Trout body: lay a full fish silhouette mask over the background. Olive gold at 18 PSI, 0.3 mm needle, 10 cm, heavier along the back, lighter toward the belly.
Red band: freehand or use a thin curved shield. Crimson rose at 15 PSI, 0.2 mm needle, 5 cm. Run the stripe nose to tail and blush the gill plate.
Spots and detail: no mask or a small dot stencil. Spot black at 12 PSI, 0.2 mm needle, 3 cm. Speckle the back, fins and tail; outline the eye and fin edges.
Splash: Spray white at 15 PSI, 0.2 mm needle, 5 cm for the bright edges, then drop to 8 PSI from 20 cm for scattered droplets. Add a thin highlight along the belly.
Peel all tape and masks slowly. Let the paint dry fully, then heat-set or cure as your paint maker directs.
Seal with a clear topcoat compatible with your paint, two light passes from 20 cm, and let it cure before wear.
Cure
- Heat set at 300°F / 150°C. Water-based textile paint is not wash-fast until it is heat set.
- Cap press: 3–5 minutes with a teflon sheet over the design.
- Or heat gun: 2–3 minutes per panel, keeping it moving 2–3 in off the fabric so it does not scorch.
- If you have neither, air cure for 72 hours before the cap touches water.
Seal
- Two light coats of matte fabric sealer, UV-resistant, from 8–10 in, 15 minutes apart.
- Leave it 24 hours before the cap is worn.
- Never a gloss sealer on cotton twill: it shines, cracks along the creases and looks like a sticker.
Clean-up
- Flush the brush with water, then airbrush cleaner, until it sprays clear.
- Strip the needle and wipe it toward the tip, never away from it.
- Never soak the brush body overnight.
Common mistakes
- A hard-edged red stripe looks painted on. Spray it close and soft, and feather both edges.
- Black spots in neat rows look like a pattern. Vary size and spacing, and cluster a few near the tail.
- Too much white turns the splash into fog. Build it in short bursts and stop while the green still shows through.
- Sealing too early clouds the colours. Wait until the paint is fully cured.
Tips
- Keep the fish silhouette mask from layer four and reuse it to protect the body while you add more splash later.
- Speckle the trout from the back toward the belly, making spots smaller and fewer as you go down the flank.
- Lower the pressure for the droplet spatter; a stuttering trigger gives a more natural spray.
- Keep a little amber in the white water near the sun so the splash looks lit from the same side.
Every kit size
Trucker · kit for 1 hat
$224
Bought separately $249 · you save $25
Includes Starter airbrush set · Cap jig · and 7 more
Every item in this kit · 9 items
Blanks
- Trucker blank, natural cotton twill front$9
Stencils
- Pre-cut mylar stencil set for this design — 7 layers$18
Paint & masks
- Water-based textile airbrush colour, 2 oz — one per colour in this design$42
- Transparent base and reducer, 4 oz$7
- Low-tack masking film and ¼ in tape$8
- Matte fabric sealer, 4 oz$12
Equipment
- Starter airbrush set — 0.3 mm dual-action gravity brush, mini compressor, braided hose$129
- Cap jig — holds the crown taut while you spray$24
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 hats
$1,073
$89.42 a hat
Bought separately $1,220 · you save $147
Includes Dual-action gravity-feed airbrush · Quiet compressor with tank and moisture trap · Cap jig and two spare crown forms · Tabletop spray booth with exhaust fan · and 11 more
Every item in this kit · 15 items
Blanks
- Trucker blank, natural cotton twill front$78
Stencils
- Desktop stencil cutter, 12 in — the "stencil printer": cuts mylar from this design's layer files$299
- Stencil mylar, 7 mil, 12 × 12 in$22
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 4 oz — one per colour in this design$98
- Transparent base and reducer, 16 oz$16
- Low-tack masking film$18
- Matte fabric sealer, 16 oz$28
Equipment
- Dual-action gravity-feed airbrush, 0.3 mm$135
- Quiet compressor with tank and moisture trap$179
- Cap jig and two spare crown forms$64
- Tabletop spray booth with exhaust fan$149
- Cleaning pot, brushes and a half-mask respirator$99
- Heat gun for curing$35
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 × 12 hats
$3,124
$21.69 a hat
Bought separately $3,676 · you save $552
Includes Two dual-action gravity-feed airbrushes · Production airbrush · Twin-piston compressor with tank and two regulators · Production spray booth · and 13 more
Every item in this kit · 17 items
Blanks
- Trucker blank, natural cotton twill front$756
Stencils
- Stencil cutter-plotter, 24 in — the production "stencil printer"$649
- Stencil mylar, 7 mil, 12 × 12 in$85
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 32 oz — one per colour in this design$336
- Transparent base and reducer$49
- Low-tack masking film$54
- Matte fabric sealer$89
Equipment
- Two dual-action gravity-feed airbrushes, 0.3 mm$270
- Production airbrush, 0.5 mm, for base fades$95
- Twin-piston compressor with tank and two regulators$329
- Production spray booth, two fans$289
- Three cap jigs$192
- Cleaning station, respirator and spare cartridges$139
- Cap heat press for curing$279
- Drying rack, 24 caps$65
Guide
- Printed step-by-step guide for this designIncluded
The creator
Remixes
No remixes yet — make your own version.
Where this came from
trucker hat · made
0 — nothing entered the score yet, at the Derby's published weights, since . Views are not counted.
- rainbow trout
- trout
- fly fishing
- sunrise
- leaping fish
- river
- splash
- trucker hat
- fishing hat
- trout art
- red band
- speckled