Sundown Rainbow Trout Trucker Hat
by @dekasso
Last light, and the river finally moves.
A painterly rainbow trout rising to a mayfly on a gold-lit evening river, in violet, ochre and rose, for long days on the water.
A rainbow trout lunges from a dusk river toward a mayfly resting on the water, with rings spreading out beneath it. It is coloured in dusky violet, gold ochre and slate blue, with a rose pink stripe down the trout's flank.
- Rainbow trout rising to a mayfly
- Dusky violet sky fading to gold
- Rose pink stripe along the trout's flank
- Rise rings on slate blue water
- Rust brown buttes on the horizon
The cap
One design, four caps. The front panel is what the paint or the dye sits on, so it changes the hat.
Trucker
The house cap — structured mid profile, foam-and-mesh back, snapback.
Specs
- Profile
- Mid profile
- Build
- 6-panel · Structured — buckram behind the front
- Crown
- 3½ in (8.9 cm)
- Visor
- Pre-curved, 2¾ in (7 cm)
- Closure
- Snapback
- Adjusts to
- 21½–24 in (54.5–61 cm)
- Airbrushed on
- Natural cotton twill
- Sublimated on
- White polyester foam
Rope cap
Structured five-panel with a near-flat brim and a cord across it.
Specs
- Profile
- Mid-high profile
- Build
- 5-panel · Structured
- Crown
- 4 in (10.2 cm)
- Visor
- Near-flat, 2⅞ in (7.3 cm), contrast rope
- Closure
- Snapback
- Adjusts to
- 21½–23¾ in (54.5–60.5 cm)
- Airbrushed on
- Stone cotton twill
- Sublimated on
- White polyester twill
Dad hat
Soft, low and unstructured — washed cotton with a strap back.
Specs
- Profile
- Low profile
- Build
- 6-panel · Unstructured — soft front
- Crown
- 3¼ in (8.3 cm)
- Visor
- Curved, 2¾ in (7 cm)
- Closure
- Strap back, brass buckle
- Adjusts to
- 21–23½ in (53.5–59.5 cm)
- Airbrushed on
- Washed khaki cotton
- Sublimated on
- White polyester twill
Five-panel camp
Flat brim, low crown, packs flat in a vest pocket.
Specs
- Profile
- Low profile
- Build
- 5-panel · Unstructured
- Crown
- 3¼ in (8.3 cm)
- Visor
- Flat, 2½ in (6.4 cm)
- Closure
- Strap back, side-release clip
- Adjusts to
- 21½–23½ in (54.5–59.5 cm)
- Airbrushed on
- Field olive nylon-cotton
- Sublimated on
- White polyester
Fit
| Cap | Profile | Crown height | Visor | Adjusts to |
|---|---|---|---|---|
| Trucker | Mid profile | 3½ in (8.9 cm) | Pre-curved, 2¾ in (7 cm) | 21½–24 in (54.5–61 cm) |
| Rope cap | Mid-high profile | 4 in (10.2 cm) | Near-flat, 2⅞ in (7.3 cm), contrast rope | 21½–23¾ in (54.5–60.5 cm) |
| Dad hat | Low profile | 3¼ in (8.3 cm) | Curved, 2¾ in (7 cm) | 21–23½ in (53.5–59.5 cm) |
| Five-panel camp | Low profile | 3¼ in (8.3 cm) | Flat, 2½ in (6.4 cm) | 21½–23½ in (54.5–59.5 cm) |
One size per cap. Run a tape around your head just above the ears, keeping it level — anything inside the range above will close on it.
Two finishes
The same design, made two ways. Pick one in the panel; the cap and the quantity are yours to choose too.
Hand airbrushed
$85 for one hat, on a trucker
Painted to order — would ship in about 2 weeks
How it is made
- How it is made
- Sprayed by hand through this design's own stencils, one layer at a time, each left to dry before the next mask goes down.
- How it looks
- Soft gradients and hand-cut stencil edges. Every cap is a little different.
- What it sits on
- On a natural cotton twill front.
- Durability and care
- Water-based paint, heat set and sealed. It takes rain and a season on a boat; spot clean with cool water, never a washing machine.
Sublimation printed
$32 for one hat, on a trucker
Printed to order — would ship in 5–7 business days
How it is made
- How it is made
- The design is printed in dye onto transfer paper, then pressed with heat so the dye soaks into the polyester fibres.
- How it looks
- Full colour edge to edge, and identical every time.
- What it sits on
- On a white polyester foam front — sublimation only takes on white polyester.
- Durability and care
- The dye is in the fibre, not on it, so it will not crack or peel. Gentle wash, air dry.
The artwork
A rainbow trout comes up out of slate blue water with its mouth open. A pale mayfly stands on the surface, wings tall and veined. Behind them the sky turns from dusky violet to gold over rust brown buttes, and a dark-haired figure watches from the left edge.
It wears like the hour it shows. Pull it on for the evening hatch, the drive home or the porch after. People tend to spot the pink stripe first, then the mayfly, then the gold streak on the water.
Mayfly wings are the part to slow down on. Lay the cream thin so the violet sky still shows through, then add the black veins with a fine needle and a very short distance.
What arrives
- The hat
- A care card
- On a hand airbrushed hat, a numbered tag naming the water it was painted from, when the design names one
Looking after it
Hand airbrushed
- Spot clean with cool water and a soft brush. Never a washing machine.
- Keep it out of a hot car for long stretches — heat-set paint is tough, but a dashboard in July is not a test worth running.
- Reshape the brim by hand while damp.
Sublimation printed
- Spot clean, or gently hand wash in cool water. No bleach.
- Air dry. Do not iron the print.
- Reshape the brim by hand while damp.
- The dye is in the fibre, so the print will not crack or peel.
Details
Airbrush palette
- Colours
- dusky violet, gold ochre, rust brown, slate blue, olive, rose pink, cream, black
Details
- Subject
- rainbow trout
- Style
- painterly illustration
Make it yourself
The palette
- Dusky violet
- Gold ochre
- Rust brown
- Slate blue
- Olive
- Rose pink
- Cream
- Black
The layers
10 layers, in this order. Each mask comes off and the paint has to dry before the next one goes down.
- Sky
- Low sun
- Distant rock
- Water
- Watcher
- Trout back
- Stripe
- Mayfly
- Detail
- Highlights
The kit's stencil set is cut from these layers; with the cutter (12 hats and up) you cut your own from this design's layer files.
How to mix each colour
Dusky violet
2 parts blue, 1 part red, a drop of white to keep it from going muddy
Gold ochre
3 parts yellow, 1 part brown, a touch of white so it stays opaque
Rust brown
2 parts orange, 1 part brown, a drop of red
Slate blue
White with blue and a touch of black, about 4 : 1 : ½
Olive
2 parts yellow, 1 part black, a drop of red to warm it
Rose pink
1 part red to 4 parts white, a drop of blue if it looks salmon
Cream
White with a drop of yellow and the smallest touch of brown
Black
Black from the bottle, sprayed in light passes; a heavy coat bleeds
Setup
- Ventilation or a spray booth. Water-based paint still throws a fine mist, and you will be breathing it for hours.
- A half-mask respirator rated for paint mists. A dust mask is not one.
- A compressor with a moisture trap, set and tested on a card before you start: wet air spits water into the paint.
- Reducer and a cleaning pot within reach, so a clog is a ten-second fix instead of a ruined panel.
- Spray a test card for every colour before it touches the cap. Colour reads differently wet, dry and on twill.
Prep
- Lint-roll the front panel. Every fibre left on it prints as a speck in the paint.
- Mask the mesh, any seams you want clean and the whole visor, underside included, with low-tack tape and paper.
- Stretch the crown over the cap jig so the front panel is taut and curved the way it will be worn. Spraying a slack panel flat distorts the design when it is worn.
- Spray one light coat of transparent base so the colour sits on the fabric instead of soaking into it.
Layer by layer
1 · Sky — 0.5 mm · 25–30 PSI
dusky violet — a deep fade from the top edge down toward the horizon
Mask None on the panel itself: the mesh and the visor are already masked from the prep.
Colour Dusky violet — 2 parts blue, 1 part red, a drop of white to keep it from going muddy
- Needle
- 0.5 mm (a 0.35 mm works, it just takes longer)
- Pressure
- 25–30 PSI
- Distance
- 6–8 in from the panel
- Passes
- 3–4 light passes, building the colour
- Dry
- 10 minutes, or 60–90 seconds with a heat gun on low, before the next mask goes down
Tip Fade wet to dry and never lay one heavy coat: twill wicks paint sideways and the edge blooms.
2 · Low sun — 0.35 mm · 20–25 PSI
gold ochre — a warm band of light along the horizon and a bright streak across the water
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Gold ochre — 3 parts yellow, 1 part brown, a touch of white so it stays opaque
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
3 · Distant rock — 0.35 mm · 20–25 PSI
rust brown — far buttes and a rock wall on the left horizon
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Rust brown — 2 parts orange, 1 part brown, a drop of red
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
4 · Water — 0.35 mm · 20–25 PSI
slate blue — the river surface with rings spreading out from the rise
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Slate blue — White with blue and a touch of black, about 4 : 1 : ½
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
5 · Watcher — 0.35 mm · 20–25 PSI
olive — a dark-haired figure at the far left edge, in shadow
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Olive — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
6 · Trout back — 0.3 mm · 18–22 PSI
olive — the back and upper flank of the leaping trout, plus the tail and fins
Mask The hand-cut subject stencil, inner pieces first, then the outline piece.
Colour Olive — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.3 mm
- Pressure
- 18–22 PSI
- Distance
- 3–4 in from the panel
- Passes
- 2–3 passes per tone, light to dark
- Dry
- 10 minutes between tones
Tip Light tones first: a light colour over a dark one needs many coats, a dark one over a light one needs two.
7 · Stripe — 0.35 mm · 20–25 PSI
rose pink — the lateral band and the gill plate of the trout
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Rose pink — 1 part red to 4 parts white, a drop of blue if it looks salmon
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
8 · Mayfly — 0.35 mm · 20–25 PSI
cream — the tall veined wings and the long slender body of the mayfly on the water
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Cream — White with a drop of yellow and the smallest touch of brown
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
9 · Detail — 0.35 mm · 20–25 PSI
black — trout spots, the eye, the open mouth, mayfly veins, legs and tails, and all outlines
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Black — Black from the bottle, sprayed in light passes; a heavy coat bleeds
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
10 · Highlights — 0.2–0.3 mm · 12–15 PSI
cream — rise rings, a glint in the trout's eye, the belly and the fin edges
Mask None: freehand, with a shield card held against any hard edge.
Colour Cream — White with a drop of yellow and the smallest touch of brown
- Needle
- 0.2–0.3 mm
- Pressure
- 12–15 PSI
- Distance
- 1–2 in from the panel
- Passes
- Freehand, in short controlled strokes
- Dry
- 10 minutes, then check it before you cure
Tip Low pressure, close in and moving: stop the stroke before you release the trigger.
Step by step
Mask the full artwork area. Spray dusky violet across the top in soft passes, fading downward. Starting point: 20 PSI, 0.5 mm needle, 15 cm distance.
Lift the horizon mask. Spray gold ochre in a narrow band along the horizon and a streak down the water. Start around 18 PSI, 0.35 mm needle, 10 cm.
Use the butte mask. Fill the far rock shapes with rust brown, a little heavier at the base. Start at 18 PSI, 0.35 mm needle, 8 cm.
Mask the sky. Spray slate blue across the water, leaving the gold streak bright. Start near 20 PSI, 0.5 mm needle, 12 cm.
Cut the figure mask at the left edge. Fill it with olive, kept dark and low in contrast. Start at 16 PSI, 0.35 mm needle, 6 cm.
Place the trout mask. Spray olive over the back, tail and fins, fading toward the belly. Start at 18 PSI, 0.35 mm needle, 8 cm.
Mask a curved band down the flank and the gill plate. Spray rose pink in light passes. Start at 15 PSI, 0.35 mm needle, 6 cm.
Use the mayfly mask. Spray cream thinly on the wings and the slender body. Start at 15 PSI, 0.2 mm needle, 5 cm.
Go freehand or with fine stencils in black for trout spots, eye, mouth, mayfly veins, legs, tails and outlines. Start at 12 PSI, 0.2 mm needle, 2 to 3 cm.
Add cream highlights to the rise rings, the eye glint, the belly and the fin edges. Start at 12 PSI, 0.2 mm needle, 3 cm.
Treat every setting above as a starting point. Test on scrap first and adjust for your paint and the room.
Let the paint cure for at least 24 hours somewhere dry and dust-free, then heat set it if your paint calls for it.
Seal with two light coats of a flexible fabric sealer, letting each one dry fully.
Cure
- Heat set at 300°F / 150°C. Water-based textile paint is not wash-fast until it is heat set.
- Cap press: 3–5 minutes with a teflon sheet over the design.
- Or heat gun: 2–3 minutes per panel, keeping it moving 2–3 in off the fabric so it does not scorch.
- If you have neither, air cure for 72 hours before the cap touches water.
Seal
- Two light coats of matte fabric sealer, UV-resistant, from 8–10 in, 15 minutes apart.
- Leave it 24 hours before the cap is worn.
- Never a gloss sealer on cotton twill: it shines, cracks along the creases and looks like a sticker.
Clean-up
- Flush the brush with water, then airbrush cleaner, until it sprays clear.
- Strip the needle and wipe it toward the tip, never away from it.
- Never soak the brush body overnight.
Common mistakes
- Heavy cream on the wings goes chalky. Build it in thin passes and let the sky show through.
- The gold streak gets lost under the blue. Mask it before the water layer, or wipe it back right away.
- Black outlines can turn fuzzy at long range. Drop the pressure and come in close with the fine needle.
- Sealing too soon traps solvent and clouds the colour. Wait out the full cure.
Tips
- Keep the trout's back darkest along the spine and let it fade softly into the pink stripe. The fish will look rounded.
- Spray the rise rings as broken arcs, not full circles. Water reads better when the lines come and go.
- Leave a thin unpainted gap between the mayfly wing and the trout's mouth so the two shapes do not merge.
- Spot the trout sparingly and keep the spots smaller toward the belly.
Every kit size
Trucker · kit for 1 hat
$229
Bought separately $255 · you save $26
Includes Starter airbrush set · Cap jig · and 7 more
Every item in this kit · 9 items
Blanks
- Trucker blank, natural cotton twill front$9
Stencils
- Pre-cut mylar stencil set for this design — 10 layers$18
Paint & masks
- Water-based textile airbrush colour, 2 oz — one per colour in this design$48
- Transparent base and reducer, 4 oz$7
- Low-tack masking film and ¼ in tape$8
- Matte fabric sealer, 4 oz$12
Equipment
- Starter airbrush set — 0.3 mm dual-action gravity brush, mini compressor, braided hose$129
- Cap jig — holds the crown taut while you spray$24
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 hats
$1,085
$90.42 a hat
Bought separately $1,234 · you save $149
Includes Dual-action gravity-feed airbrush · Quiet compressor with tank and moisture trap · Cap jig and two spare crown forms · Tabletop spray booth with exhaust fan · and 11 more
Every item in this kit · 15 items
Blanks
- Trucker blank, natural cotton twill front$78
Stencils
- Desktop stencil cutter, 12 in — the "stencil printer": cuts mylar from this design's layer files$299
- Stencil mylar, 7 mil, 12 × 12 in$22
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 4 oz — one per colour in this design$112
- Transparent base and reducer, 16 oz$16
- Low-tack masking film$18
- Matte fabric sealer, 16 oz$28
Equipment
- Dual-action gravity-feed airbrush, 0.3 mm$135
- Quiet compressor with tank and moisture trap$179
- Cap jig and two spare crown forms$64
- Tabletop spray booth with exhaust fan$149
- Cleaning pot, brushes and a half-mask respirator$99
- Heat gun for curing$35
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 × 12 hats
$3,165
$21.98 a hat
Bought separately $3,724 · you save $559
Includes Two dual-action gravity-feed airbrushes · Production airbrush · Twin-piston compressor with tank and two regulators · Production spray booth · and 13 more
Every item in this kit · 17 items
Blanks
- Trucker blank, natural cotton twill front$756
Stencils
- Stencil cutter-plotter, 24 in — the production "stencil printer"$649
- Stencil mylar, 7 mil, 12 × 12 in$85
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 32 oz — one per colour in this design$384
- Transparent base and reducer$49
- Low-tack masking film$54
- Matte fabric sealer$89
Equipment
- Two dual-action gravity-feed airbrushes, 0.3 mm$270
- Production airbrush, 0.5 mm, for base fades$95
- Twin-piston compressor with tank and two regulators$329
- Production spray booth, two fans$289
- Three cap jigs$192
- Cleaning station, respirator and spare cartridges$139
- Cap heat press for curing$279
- Drying rack, 24 caps$65
Guide
- Printed step-by-step guide for this designIncluded
The creator
Remixes
No remixes yet — make your own version.
Where this came from
trucker hat · made
0 — nothing entered the score yet, at the Derby's published weights, since . Views are not counted.
- rainbow trout
- mayfly
- evening hatch
- dry fly
- rise
- trout hat
- fly fishing
- sunset
- river
- trucker hat