Misty Mayfly Trout Trucker Hat
by @dekasso
One mayfly, one trout, a breath apart.
A mayfly on river stones facing a rising trout below misty cliffs, in slate blue, olive gold and pale cream, made for the front of a trucker hat.
A mayfly perches on river stones while a spotted trout rises from the water to meet it, with tall rock walls fading into mist behind. The scene is coloured in slate blue and mist grey, with an olive gold fish and pale cream wings.
- Mayfly perched on grey river stones
- Spotted trout rising, mouth wide open
- Slate blue cliffs fading into mist
- Olive gold, pale cream and charcoal details
The cap
One design, four caps. The front panel is what the paint or the dye sits on, so it changes the hat.
Trucker
The house cap — structured mid profile, foam-and-mesh back, snapback.
Specs
- Profile
- Mid profile
- Build
- 6-panel · Structured — buckram behind the front
- Crown
- 3½ in (8.9 cm)
- Visor
- Pre-curved, 2¾ in (7 cm)
- Closure
- Snapback
- Adjusts to
- 21½–24 in (54.5–61 cm)
- Airbrushed on
- Natural cotton twill
- Sublimated on
- White polyester foam
Rope cap
Structured five-panel with a near-flat brim and a cord across it.
Specs
- Profile
- Mid-high profile
- Build
- 5-panel · Structured
- Crown
- 4 in (10.2 cm)
- Visor
- Near-flat, 2⅞ in (7.3 cm), contrast rope
- Closure
- Snapback
- Adjusts to
- 21½–23¾ in (54.5–60.5 cm)
- Airbrushed on
- Stone cotton twill
- Sublimated on
- White polyester twill
Dad hat
Soft, low and unstructured — washed cotton with a strap back.
Specs
- Profile
- Low profile
- Build
- 6-panel · Unstructured — soft front
- Crown
- 3¼ in (8.3 cm)
- Visor
- Curved, 2¾ in (7 cm)
- Closure
- Strap back, brass buckle
- Adjusts to
- 21–23½ in (53.5–59.5 cm)
- Airbrushed on
- Washed khaki cotton
- Sublimated on
- White polyester twill
Five-panel camp
Flat brim, low crown, packs flat in a vest pocket.
Specs
- Profile
- Low profile
- Build
- 5-panel · Unstructured
- Crown
- 3¼ in (8.3 cm)
- Visor
- Flat, 2½ in (6.4 cm)
- Closure
- Strap back, side-release clip
- Adjusts to
- 21½–23½ in (54.5–59.5 cm)
- Airbrushed on
- Field olive nylon-cotton
- Sublimated on
- White polyester
Fit
| Cap | Profile | Crown height | Visor | Adjusts to |
|---|---|---|---|---|
| Trucker | Mid profile | 3½ in (8.9 cm) | Pre-curved, 2¾ in (7 cm) | 21½–24 in (54.5–61 cm) |
| Rope cap | Mid-high profile | 4 in (10.2 cm) | Near-flat, 2⅞ in (7.3 cm), contrast rope | 21½–23¾ in (54.5–60.5 cm) |
| Dad hat | Low profile | 3¼ in (8.3 cm) | Curved, 2¾ in (7 cm) | 21–23½ in (53.5–59.5 cm) |
| Five-panel camp | Low profile | 3¼ in (8.3 cm) | Flat, 2½ in (6.4 cm) | 21½–23½ in (54.5–59.5 cm) |
One size per cap. Run a tape around your head just above the ears, keeping it level — anything inside the range above will close on it.
Two finishes
The same design, made two ways. Pick one in the panel; the cap and the quantity are yours to choose too.
Hand airbrushed
$85 for one hat, on a trucker
Painted to order — would ship in about 2 weeks
How it is made
- How it is made
- Sprayed by hand through this design's own stencils, one layer at a time, each left to dry before the next mask goes down.
- How it looks
- Soft gradients and hand-cut stencil edges. Every cap is a little different.
- What it sits on
- On a natural cotton twill front.
- Durability and care
- Water-based paint, heat set and sealed. It takes rain and a season on a boat; spot clean with cool water, never a washing machine.
Sublimation printed
$32 for one hat, on a trucker
Printed to order — would ship in 5–7 business days
How it is made
- How it is made
- The design is printed in dye onto transfer paper, then pressed with heat so the dye soaks into the polyester fibres.
- How it looks
- Full colour edge to edge, and identical every time.
- What it sits on
- On a white polyester foam front — sublimation only takes on white polyester.
- Durability and care
- The dye is in the fibre, not on it, so it will not crack or peel. Gentle wash, air dry.
The artwork
A mayfly stands tall on a pile of round grey stones, wings up, tails trailing. To the right a spotted trout pushes out of the river with its mouth already open. Behind them, slate blue cliffs drift back into a pale, foggy sky.
Wear it to the river at first light, when the water looks just like this. People see the fish first, then catch the little insect waiting on the rocks, and the story clicks.
Thin passes of pale cream make the mayfly wings look like they hold light. Build them up slowly, then pull the charcoal veins through last so the wings stay see-through rather than solid.
What arrives
- The hat
- A care card
- On a hand airbrushed hat, a numbered tag naming the water it was painted from, when the design names one
Looking after it
Hand airbrushed
- Spot clean with cool water and a soft brush. Never a washing machine.
- Keep it out of a hot car for long stretches — heat-set paint is tough, but a dashboard in July is not a test worth running.
- Reshape the brim by hand while damp.
Sublimation printed
- Spot clean, or gently hand wash in cool water. No bleach.
- Air dry. Do not iron the print.
- Reshape the brim by hand while damp.
- The dye is in the fibre, so the print will not crack or peel.
Details
Airbrush palette
- Colours
- mist grey, slate blue, charcoal, olive gold, pale cream, white
Details
- Subject
- mayfly and rising trout
- Style
- painterly realism
Make it yourself
The palette
- Mist grey
- Slate blue
- Charcoal
- Olive gold
- Pale cream
- White
The layers
7 layers, in this order. Each mask comes off and the paint has to dry before the next one goes down.
- Sky
- Cliffs
- River stones
- Trout
- Mayfly
- Details
- Highlights
The kit's stencil set is cut from these layers; with the cutter (12 hats and up) you cut your own from this design's layer files.
How to mix each colour
Mist grey
4 parts white, 1 part black; a drop of blue for cool grey, a drop of brown for warm stone
Slate blue
White with blue and a touch of black, about 4 : 1 : ½
Charcoal
1 part white to 3 parts black, a drop of blue
Olive gold
2 parts yellow, 1 part black, a drop of red to warm it
Pale cream
White with a drop of yellow and the smallest touch of brown
White
Opaque white from the bottle; two thin coats cover better than one thick one
Setup
- Ventilation or a spray booth. Water-based paint still throws a fine mist, and you will be breathing it for hours.
- A half-mask respirator rated for paint mists. A dust mask is not one.
- A compressor with a moisture trap, set and tested on a card before you start: wet air spits water into the paint.
- Reducer and a cleaning pot within reach, so a clog is a ten-second fix instead of a ruined panel.
- Spray a test card for every colour before it touches the cap. Colour reads differently wet, dry and on twill.
Prep
- Lint-roll the front panel. Every fibre left on it prints as a speck in the paint.
- Mask the mesh, any seams you want clean and the whole visor, underside included, with low-tack tape and paper.
- Stretch the crown over the cap jig so the front panel is taut and curved the way it will be worn. Spraying a slack panel flat distorts the design when it is worn.
- Spray one light coat of transparent base so the colour sits on the fabric instead of soaking into it.
Layer by layer
1 · Sky — 0.5 mm · 25–30 PSI
mist grey — a pale fade across the top and down into the far distance
Mask None on the panel itself: the mesh and the visor are already masked from the prep.
Colour Mist grey — 4 parts white, 1 part black; a drop of blue for cool grey, a drop of brown for warm stone
- Needle
- 0.5 mm (a 0.35 mm works, it just takes longer)
- Pressure
- 25–30 PSI
- Distance
- 6–8 in from the panel
- Passes
- 3–4 light passes, building the colour
- Dry
- 10 minutes, or 60–90 seconds with a heat gun on low, before the next mask goes down
Tip Fade wet to dry and never lay one heavy coat: twill wicks paint sideways and the edge blooms.
2 · Cliffs — 0.35 mm · 20–25 PSI
slate blue — tall rock walls stepping back on both sides of the river
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Slate blue — White with blue and a touch of black, about 4 : 1 : ½
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
3 · River stones — 0.35 mm · 20–25 PSI
charcoal — rounded rocks piled at lower left under the insect
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Charcoal — 1 part white to 3 parts black, a drop of blue
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
4 · Trout — 0.3 mm · 18–22 PSI
olive gold — the fish rising from the right, jaw open, body angled toward the mayfly
Mask The hand-cut subject stencil, inner pieces first, then the outline piece.
Colour Olive gold — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.3 mm
- Pressure
- 18–22 PSI
- Distance
- 3–4 in from the panel
- Passes
- 2–3 passes per tone, light to dark
- Dry
- 10 minutes between tones
Tip Light tones first: a light colour over a dark one needs many coats, a dark one over a light one needs two.
5 · Mayfly — 0.35 mm · 20–25 PSI
pale cream — upright wings, segmented body and long tails on the stones
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Pale cream — White with a drop of yellow and the smallest touch of brown
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
6 · Details — 0.35 mm · 20–25 PSI
charcoal — trout spots, gill line, eye, mayfly legs, antennae, wing veins and stone shadows
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Charcoal — 1 part white to 3 parts black, a drop of blue
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
7 · Highlights — 0.2–0.3 mm · 12–15 PSI
white — glints on the stones, ripples on the water, light along the wing edges and the trout's belly
Mask None: freehand, with a shield card held against any hard edge.
Colour White — Opaque white from the bottle; two thin coats cover better than one thick one
- Needle
- 0.2–0.3 mm
- Pressure
- 12–15 PSI
- Distance
- 1–2 in from the panel
- Passes
- Freehand, in short controlled strokes
- Dry
- 10 minutes, then check it before you cure
Tip Low pressure, close in and moving: stop the stroke before you release the trigger.
Step by step
Mask the whole design area, then spray mist grey across the top as a soft fade. Start around 20 PSI, 0.3 mm needle, 15 cm away; treat every setting here as a starting point.
Cut the cliff mask and lay slate blue in light passes, darker at the base of each wall. Try 20 PSI, 0.3 mm needle, 10–12 cm, and let the edges blur into the mist.
Mask the river stones at lower left and spray charcoal, leaving the tops lighter. Start at 18 PSI, 0.3 mm needle, 8–10 cm.
Mask the trout shape and fill it with olive gold, deepest along the back. Try 18 PSI, 0.3 mm needle, 8 cm.
Mask the mayfly and spray pale cream for the wings, body and tails in thin, see-through coats. Start at 15 PSI, 0.2 mm needle, 5–6 cm.
Switch to charcoal for the details: trout spots, eye, gill line, mayfly legs, antennae, wing veins and shadows under the stones. Try 12–15 PSI, 0.2 mm needle, 2–4 cm, freehand or with fine masks.
Finish with white highlights on stone tops, water ripples, wing edges and the trout's belly. Start at 12 PSI, 0.2 mm needle, 3–5 cm, in short bursts.
Let the design dry fully, cure it following your paint's directions, then seal it as that same paint recommends.
Cure
- Heat set at 300°F / 150°C. Water-based textile paint is not wash-fast until it is heat set.
- Cap press: 3–5 minutes with a teflon sheet over the design.
- Or heat gun: 2–3 minutes per panel, keeping it moving 2–3 in off the fabric so it does not scorch.
- If you have neither, air cure for 72 hours before the cap touches water.
Seal
- Two light coats of matte fabric sealer, UV-resistant, from 8–10 in, 15 minutes apart.
- Leave it 24 hours before the cap is worn.
- Never a gloss sealer on cotton twill: it shines, cracks along the creases and looks like a sticker.
Clean-up
- Flush the brush with water, then airbrush cleaner, until it sprays clear.
- Strip the needle and wipe it toward the tip, never away from it.
- Never soak the brush body overnight.
Common mistakes
- Spraying the wings too heavy makes them flat and chalky; build pale cream in several thin passes.
- Charcoal fine lines that spider at the ends come from too much pressure; lower PSI and move closer.
- White highlights everywhere flatten the scene; keep them to the brightest edges only.
- Rushing between layers smears masks; let each colour dry to the touch before cutting the next.
Tips
- Test each colour on scrap first; olive gold can shift warmer or cooler depending on what sits under it.
- Keep the cliffs soft and the fish and insect sharp, so the eye lands on the meeting point.
- Space the trout spots unevenly and vary their size for a living, natural look.
- Lift masks slowly while the last coat is still slightly tacky to keep clean edges.
Every kit size
Trucker · kit for 1 hat
$218
Bought separately $243 · you save $25
Includes Starter airbrush set · Cap jig · and 7 more
Every item in this kit · 9 items
Blanks
- Trucker blank, natural cotton twill front$9
Stencils
- Pre-cut mylar stencil set for this design — 7 layers$18
Paint & masks
- Water-based textile airbrush colour, 2 oz — one per colour in this design$36
- Transparent base and reducer, 4 oz$7
- Low-tack masking film and ¼ in tape$8
- Matte fabric sealer, 4 oz$12
Equipment
- Starter airbrush set — 0.3 mm dual-action gravity brush, mini compressor, braided hose$129
- Cap jig — holds the crown taut while you spray$24
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 hats
$1,061
$88.42 a hat
Bought separately $1,206 · you save $145
Includes Dual-action gravity-feed airbrush · Quiet compressor with tank and moisture trap · Cap jig and two spare crown forms · Tabletop spray booth with exhaust fan · and 11 more
Every item in this kit · 15 items
Blanks
- Trucker blank, natural cotton twill front$78
Stencils
- Desktop stencil cutter, 12 in — the "stencil printer": cuts mylar from this design's layer files$299
- Stencil mylar, 7 mil, 12 × 12 in$22
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 4 oz — one per colour in this design$84
- Transparent base and reducer, 16 oz$16
- Low-tack masking film$18
- Matte fabric sealer, 16 oz$28
Equipment
- Dual-action gravity-feed airbrush, 0.3 mm$135
- Quiet compressor with tank and moisture trap$179
- Cap jig and two spare crown forms$64
- Tabletop spray booth with exhaust fan$149
- Cleaning pot, brushes and a half-mask respirator$99
- Heat gun for curing$35
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 × 12 hats
$3,083
$21.41 a hat
Bought separately $3,628 · you save $545
Includes Two dual-action gravity-feed airbrushes · Production airbrush · Twin-piston compressor with tank and two regulators · Production spray booth · and 13 more
Every item in this kit · 17 items
Blanks
- Trucker blank, natural cotton twill front$756
Stencils
- Stencil cutter-plotter, 24 in — the production "stencil printer"$649
- Stencil mylar, 7 mil, 12 × 12 in$85
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 32 oz — one per colour in this design$288
- Transparent base and reducer$49
- Low-tack masking film$54
- Matte fabric sealer$89
Equipment
- Two dual-action gravity-feed airbrushes, 0.3 mm$270
- Production airbrush, 0.5 mm, for base fades$95
- Twin-piston compressor with tank and two regulators$329
- Production spray booth, two fans$289
- Three cap jigs$192
- Cleaning station, respirator and spare cartridges$139
- Cap heat press for curing$279
- Drying rack, 24 caps$65
Guide
- Printed step-by-step guide for this designIncluded
The creator
Remixes
No remixes yet — make your own version.
Where this came from
trucker hat · made
0 — nothing entered the score yet, at the Derby's published weights, since . Views are not counted.
- mayfly
- trout
- rising trout
- fly fishing
- trucker hat
- river
- river stones
- cliffs
- mist
- slate blue
- olive gold
- dry fly