Platte Rainbow Trout Trucker Hat
by @dekasso
Under the riffle, three trout holding
A split-view river scene of three rainbow trout below a pine canyon, in teal, olive and rust, made for days on the water.
Three rainbow trout hold over a stony riverbed beneath a pine-lined canyon, with the river cut in half at the waterline. River teal, moss olive and canyon rust carry the scene, and a trout pink stripe runs down each fish.
- Three rainbow trout below the waterline
- Pine canyon and blue peaks above
- River teal, moss olive and canyon rust
- Pink stripe and charcoal spots on each fish
- Sun gold light across the riverbed stones
The cap
One design, four caps. The front panel is what the paint or the dye sits on, so it changes the hat.
Trucker
The house cap — structured mid profile, foam-and-mesh back, snapback.
Specs
- Profile
- Mid profile
- Build
- 6-panel · Structured — buckram behind the front
- Crown
- 3½ in (8.9 cm)
- Visor
- Pre-curved, 2¾ in (7 cm)
- Closure
- Snapback
- Adjusts to
- 21½–24 in (54.5–61 cm)
- Airbrushed on
- Natural cotton twill
- Sublimated on
- White polyester foam
Rope cap
Structured five-panel with a near-flat brim and a cord across it.
Specs
- Profile
- Mid-high profile
- Build
- 5-panel · Structured
- Crown
- 4 in (10.2 cm)
- Visor
- Near-flat, 2⅞ in (7.3 cm), contrast rope
- Closure
- Snapback
- Adjusts to
- 21½–23¾ in (54.5–60.5 cm)
- Airbrushed on
- Stone cotton twill
- Sublimated on
- White polyester twill
Dad hat
Soft, low and unstructured — washed cotton with a strap back.
Specs
- Profile
- Low profile
- Build
- 6-panel · Unstructured — soft front
- Crown
- 3¼ in (8.3 cm)
- Visor
- Curved, 2¾ in (7 cm)
- Closure
- Strap back, brass buckle
- Adjusts to
- 21–23½ in (53.5–59.5 cm)
- Airbrushed on
- Washed khaki cotton
- Sublimated on
- White polyester twill
Five-panel camp
Flat brim, low crown, packs flat in a vest pocket.
Specs
- Profile
- Low profile
- Build
- 5-panel · Unstructured
- Crown
- 3¼ in (8.3 cm)
- Visor
- Flat, 2½ in (6.4 cm)
- Closure
- Strap back, side-release clip
- Adjusts to
- 21½–23½ in (54.5–59.5 cm)
- Airbrushed on
- Field olive nylon-cotton
- Sublimated on
- White polyester
Fit
| Cap | Profile | Crown height | Visor | Adjusts to |
|---|---|---|---|---|
| Trucker | Mid profile | 3½ in (8.9 cm) | Pre-curved, 2¾ in (7 cm) | 21½–24 in (54.5–61 cm) |
| Rope cap | Mid-high profile | 4 in (10.2 cm) | Near-flat, 2⅞ in (7.3 cm), contrast rope | 21½–23¾ in (54.5–60.5 cm) |
| Dad hat | Low profile | 3¼ in (8.3 cm) | Curved, 2¾ in (7 cm) | 21–23½ in (53.5–59.5 cm) |
| Five-panel camp | Low profile | 3¼ in (8.3 cm) | Flat, 2½ in (6.4 cm) | 21½–23½ in (54.5–59.5 cm) |
One size per cap. Run a tape around your head just above the ears, keeping it level — anything inside the range above will close on it.
Two finishes
The same design, made two ways. Pick one in the panel; the cap and the quantity are yours to choose too.
Hand airbrushed
$85 for one hat, on a trucker
Painted to order — would ship in about 2 weeks
How it is made
- How it is made
- Sprayed by hand through this design's own stencils, one layer at a time, each left to dry before the next mask goes down.
- How it looks
- Soft gradients and hand-cut stencil edges. Every cap is a little different.
- What it sits on
- On a natural cotton twill front.
- Durability and care
- Water-based paint, heat set and sealed. It takes rain and a season on a boat; spot clean with cool water, never a washing machine.
Sublimation printed
$32 for one hat, on a trucker
Printed to order — would ship in 5–7 business days
How it is made
- How it is made
- The design is printed in dye onto transfer paper, then pressed with heat so the dye soaks into the polyester fibres.
- How it looks
- Full colour edge to edge, and identical every time.
- What it sits on
- On a white polyester foam front — sublimation only takes on white polyester.
- Durability and care
- The dye is in the fibre, not on it, so it will not crack or peel. Gentle wash, air dry.
The artwork
Above the line, a canyon of rust rock and dark pines leads back to blue peaks. Below it, the water turns teal and three rainbow trout hang over green and copper stones, each with a pink band and a scatter of black spots.
Wear it on the walk down to the river, or at the counter in town after. People see the fish first, then notice the whole canyon sitting on top of them.
The waterline is the line to get right. Keep a crisp edge where sky meets surface, then let the river teal fade softly downward so the trout read as underwater and the canyon reads as dry land.
The water it was painted from
South Platte RiverColorado Front Range · CO
- River
- South Platte River, Colorado Front Range
- States
- CO
- Fish
- Rainbow trout, Brown trout, Cutbow
- Water type
- Tailwater
What arrives
- The hat
- A care card
- On a hand airbrushed hat, a numbered tag naming the water it was painted from, when the design names one
Looking after it
Hand airbrushed
- Spot clean with cool water and a soft brush. Never a washing machine.
- Keep it out of a hot car for long stretches — heat-set paint is tough, but a dashboard in July is not a test worth running.
- Reshape the brim by hand while damp.
Sublimation printed
- Spot clean, or gently hand wash in cool water. No bleach.
- Air dry. Do not iron the print.
- Reshape the brim by hand while damp.
- The dye is in the fibre, so the print will not crack or peel.
Details
Airbrush palette
- Colours
- sky blue, canyon rust, pine green, river teal, moss olive, sun gold, trout pink, charcoal, cream
Details
- Subject
- rainbow trout
- Style
- split-view river scene
Make it yourself
The palette
- Sky blue
- Canyon rust
- Pine green
- River teal
- Moss olive
- Sun gold
- Trout pink
- Charcoal
- Cream
The layers
9 layers, in this order. Each mask comes off and the paint has to dry before the next one goes down.
- Sky and peaks
- Canyon
- Forest
- Water
- Riverbed
- Warm light
- Trout stripe
- Spots and shadow
- Highlights
The kit's stencil set is cut from these layers; with the cutter (12 hats and up) you cut your own from this design's layer files.
How to mix each colour
Sky blue
1 part blue to 4 parts white, a drop of green so it does not drift purple
Canyon rust
2 parts orange, 1 part brown, a drop of red
Pine green
2 parts green, 1 part black, a drop of blue to cool it
River teal
2 parts blue, 1 part green, a touch of white to lift it
Moss olive
2 parts yellow, 1 part black, a drop of red to warm it
Sun gold
3 parts yellow, 1 part brown, a touch of white so it stays opaque
Trout pink
1 part red to 4 parts white, a drop of blue if it looks salmon
Charcoal
1 part white to 3 parts black, a drop of blue
Cream
White with a drop of yellow and the smallest touch of brown
Setup
- Ventilation or a spray booth. Water-based paint still throws a fine mist, and you will be breathing it for hours.
- A half-mask respirator rated for paint mists. A dust mask is not one.
- A compressor with a moisture trap, set and tested on a card before you start: wet air spits water into the paint.
- Reducer and a cleaning pot within reach, so a clog is a ten-second fix instead of a ruined panel.
- Spray a test card for every colour before it touches the cap. Colour reads differently wet, dry and on twill.
Prep
- Lint-roll the front panel. Every fibre left on it prints as a speck in the paint.
- Mask the mesh, any seams you want clean and the whole visor, underside included, with low-tack tape and paper.
- Stretch the crown over the cap jig so the front panel is taut and curved the way it will be worn. Spraying a slack panel flat distorts the design when it is worn.
- Spray one light coat of transparent base so the colour sits on the fabric instead of soaking into it.
Layer by layer
1 · Sky and peaks — 0.5 mm · 25–30 PSI
sky blue — a pale sky over distant blue-grey mountains
Mask None on the panel itself: the mesh and the visor are already masked from the prep.
Colour Sky blue — 1 part blue to 4 parts white, a drop of green so it does not drift purple
- Needle
- 0.5 mm (a 0.35 mm works, it just takes longer)
- Pressure
- 25–30 PSI
- Distance
- 6–8 in from the panel
- Passes
- 3–4 light passes, building the colour
- Dry
- 10 minutes, or 60–90 seconds with a heat gun on low, before the next mask goes down
Tip Fade wet to dry and never lay one heavy coat: twill wicks paint sideways and the edge blooms.
2 · Canyon — 0.35 mm · 20–25 PSI
canyon rust — rocky slopes and boulders along both banks
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Canyon rust — 2 parts orange, 1 part brown, a drop of red
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
3 · Forest — 0.35 mm · 20–25 PSI
pine green — pine trees climbing the banks
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Pine green — 2 parts green, 1 part black, a drop of blue to cool it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
4 · Water — 0.35 mm · 20–25 PSI
river teal — the river surface and the soft fade below the waterline
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour River teal — 2 parts blue, 1 part green, a touch of white to lift it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
5 · Riverbed — 0.35 mm · 20–25 PSI
moss olive — rounded stones, weed and the backs of three trout
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Moss olive — 2 parts yellow, 1 part black, a drop of red to warm it
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
6 · Warm light — 0.35 mm · 20–25 PSI
sun gold — glow on the flanks and across the stones
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Sun gold — 3 parts yellow, 1 part brown, a touch of white so it stays opaque
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
7 · Trout stripe — 0.3 mm · 18–22 PSI
trout pink — the red band and cheek on each fish
Mask The hand-cut subject stencil, inner pieces first, then the outline piece.
Colour Trout pink — 1 part red to 4 parts white, a drop of blue if it looks salmon
- Needle
- 0.3 mm
- Pressure
- 18–22 PSI
- Distance
- 3–4 in from the panel
- Passes
- 2–3 passes per tone, light to dark
- Dry
- 10 minutes between tones
Tip Light tones first: a light colour over a dark one needs many coats, a dark one over a light one needs two.
8 · Spots and shadow — 0.35 mm · 20–25 PSI
charcoal — trout spots, fin edges and stone shadows
Mask Lay this layer's mylar stencil and burnish the edges flat with your thumbnail.
Colour Charcoal — 1 part white to 3 parts black, a drop of blue
- Needle
- 0.35 mm
- Pressure
- 20–25 PSI
- Distance
- 4–6 in from the panel
- Passes
- 2–3 passes
- Dry
- 10 minutes before lifting the stencil
Tip Spray away from the stencil edge, not into it, so the air does not push paint underneath.
9 · Highlights — 0.2–0.3 mm · 12–15 PSI
cream — bellies, ripples on the surface and glints on the rocks
Mask None: freehand, with a shield card held against any hard edge.
Colour Cream — White with a drop of yellow and the smallest touch of brown
- Needle
- 0.2–0.3 mm
- Pressure
- 12–15 PSI
- Distance
- 1–2 in from the panel
- Passes
- Freehand, in short controlled strokes
- Dry
- 10 minutes, then check it before you cure
Tip Low pressure, close in and moving: stop the stroke before you release the trigger.
Step by step
Mask the full panel outline, then spray sky blue across the top band for sky and distant peaks. Starting point: 20 PSI, 0.3 mm needle, 15 cm away.
Lay the canyon mask and mist canyon rust over the slopes and bank boulders at about 18 PSI, 0.3 mm needle, 10 cm. Build the tone in thin passes.
With the forest mask, spray pine green for the trees on both banks. Start near 18 PSI, 0.3 mm needle, 8 cm for sharper tree tips.
Mask a crisp waterline and spray river teal across the surface, then fade it downward into the underwater area. Try 20 PSI, 0.35 mm needle, 15 cm.
Use the riverbed and trout-body mask to spray moss olive over the stones, weed and the backs of the three trout. Start at 18 PSI, 0.3 mm needle, 10 cm.
Spray sun gold lightly over the trout flanks and the tops of the stones for warm light. About 15 PSI, 0.3 mm needle, 12 cm is a good start.
With the stripe mask, lay trout pink along each fish's lateral band and cheek. Try 15 PSI, 0.2 mm needle, 6 cm for clean edges.
Use the detail mask for charcoal: trout spots, fin edges and the shadows under stones. Start near 12 PSI, 0.2 mm needle, 4 cm.
Finish with cream on the bellies, surface ripples and rock glints. Begin at 12 PSI, 0.2 mm needle, 5 cm. All settings here are a starting point; adjust to your paint and tool.
Let the paint cure for at least 24 hours, then heat-set if your paint calls for it and seal with a clear topcoat in two light passes.
Cure
- Heat set at 300°F / 150°C. Water-based textile paint is not wash-fast until it is heat set.
- Cap press: 3–5 minutes with a teflon sheet over the design.
- Or heat gun: 2–3 minutes per panel, keeping it moving 2–3 in off the fabric so it does not scorch.
- If you have neither, air cure for 72 hours before the cap touches water.
Seal
- Two light coats of matte fabric sealer, UV-resistant, from 8–10 in, 15 minutes apart.
- Leave it 24 hours before the cap is worn.
- Never a gloss sealer on cotton twill: it shines, cracks along the creases and looks like a sticker.
Clean-up
- Flush the brush with water, then airbrush cleaner, until it sprays clear.
- Strip the needle and wipe it toward the tip, never away from it.
- Never soak the brush body overnight.
Common mistakes
- A soft waterline muddles above and below. Burnish the mask edge down firmly before the river teal goes on.
- Heavy coats of trout pink bleed under the stripe mask. Spray thin, let each pass flash, then add another.
- Charcoal sprayed too close spatters. Lower the pressure and keep a steady distance for the spots.
Tips
- Test each colour on a scrap first; river teal and moss olive can look alike until they dry side by side.
- Keep the trout spots small and uneven. A random scatter looks more like a living fish than a neat pattern.
- Let sun gold sit only on the tops of stones and flanks so the light seems to come from above the water.
Every kit size
Trucker · kit for 1 hat
$229
Bought separately $255 · you save $26
Includes Starter airbrush set · Cap jig · and 7 more
Every item in this kit · 9 items
Blanks
- Trucker blank, natural cotton twill front$9
Stencils
- Pre-cut mylar stencil set for this design — 9 layers$18
Paint & masks
- Water-based textile airbrush colour, 2 oz — one per colour in this design$48
- Transparent base and reducer, 4 oz$7
- Low-tack masking film and ¼ in tape$8
- Matte fabric sealer, 4 oz$12
Equipment
- Starter airbrush set — 0.3 mm dual-action gravity brush, mini compressor, braided hose$129
- Cap jig — holds the crown taut while you spray$24
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 hats
$1,085
$90.42 a hat
Bought separately $1,234 · you save $149
Includes Dual-action gravity-feed airbrush · Quiet compressor with tank and moisture trap · Cap jig and two spare crown forms · Tabletop spray booth with exhaust fan · and 11 more
Every item in this kit · 15 items
Blanks
- Trucker blank, natural cotton twill front$78
Stencils
- Desktop stencil cutter, 12 in — the "stencil printer": cuts mylar from this design's layer files$299
- Stencil mylar, 7 mil, 12 × 12 in$22
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 4 oz — one per colour in this design$112
- Transparent base and reducer, 16 oz$16
- Low-tack masking film$18
- Matte fabric sealer, 16 oz$28
Equipment
- Dual-action gravity-feed airbrush, 0.3 mm$135
- Quiet compressor with tank and moisture trap$179
- Cap jig and two spare crown forms$64
- Tabletop spray booth with exhaust fan$149
- Cleaning pot, brushes and a half-mask respirator$99
- Heat gun for curing$35
Guide
- Printed step-by-step guide for this designIncluded
Trucker · kit for 12 × 12 hats
$3,165
$21.98 a hat
Bought separately $3,724 · you save $559
Includes Two dual-action gravity-feed airbrushes · Production airbrush · Twin-piston compressor with tank and two regulators · Production spray booth · and 13 more
Every item in this kit · 17 items
Blanks
- Trucker blank, natural cotton twill front$756
Stencils
- Stencil cutter-plotter, 24 in — the production "stencil printer"$649
- Stencil mylar, 7 mil, 12 × 12 in$85
- This design's layer files, every layer (SVG)Included
Paint & masks
- Water-based textile airbrush colour, 32 oz — one per colour in this design$384
- Transparent base and reducer$49
- Low-tack masking film$54
- Matte fabric sealer$89
Equipment
- Two dual-action gravity-feed airbrushes, 0.3 mm$270
- Production airbrush, 0.5 mm, for base fades$95
- Twin-piston compressor with tank and two regulators$329
- Production spray booth, two fans$289
- Three cap jigs$192
- Cleaning station, respirator and spare cartridges$139
- Cap heat press for curing$279
- Drying rack, 24 caps$65
Guide
- Printed step-by-step guide for this designIncluded
The creator
Remixes
No remixes yet — make your own version.
Where this came from
trucker hat · made
0 — nothing entered the score yet, at the Derby's published weights, since . Views are not counted.
- rainbow trout
- trout
- south platte
- fly fishing
- river
- canyon
- pine
- underwater
- split view
- trucker hat
- teal
- olive